mip/Data/BulkLoad/CAVEATS.csv

1	DOCUMENT_POSITION	JOB TYPE	METER TYPE	SERVICE PRESSURE	SORT_ORDER	TEXT
2	CONT_SUM	ADVERSARIAL	DIAPHRAGM	LP	1	plus purging on time and materials basis.
3	CONT_SUM	ADVERSARIAL	DIAPHRAGM	MP	1	plus purging on time and materials basis.
4	CONT_SUM	ADVERSARIAL	DIAPHRAGM	MP	2	excluding lifting gear charges
5	CONT_SUM	ADVERSARIAL	ROTARY	LP	1	plus purging on time and materials basis.
6	CONT_SUM	ADVERSARIAL	ROTARY	LP	2	excluding lifting gear charges
7	CONT_SUM	ADVERSARIAL	ROTARY	MP	1	plus purging on time and materials basis.
8	CONT_SUM	ADVERSARIAL	ROTARY	MP	2	excluding lifting gear charges
9	CONT_SUM	ADVERSARIAL	TURBINE	LP	1	plus purging on time and materials basis.
10	CONT_SUM	ADVERSARIAL	TURBINE	LP	2	excluding lifting gear charges
11	CONT_SUM	ADVERSARIAL	TURBINE	MP	1	plus purging on time and materials basis.
12	CONT_SUM	ADVERSARIAL	TURBINE	MP	2	excluding lifting gear charges
13	CONT_SUM	EXCHANGE	DIAPHRAGM	MP	1	excluding lifting gear charges
14	CONT_SUM	EXCHANGE	ROTARY	LP	1	excluding lifting gear charges
15	CONT_SUM	EXCHANGE	ROTARY	MP	1	excluding lifting gear charges
16	CONT_SUM	EXCHANGE	TURBINE	LP	1	excluding lifting gear charges
17	CONT_SUM	EXCHANGE	TURBINE	MP	1	excluding lifting gear charges
18	CONT_SUM	INSTALL	DIAPHRAGM	MP	1	excluding lifting gear charges
19	CONT_SUM	INSTALL	ROTARY	LP	1	excluding lifting gear charges
20	CONT_SUM	INSTALL	ROTARY	MP	1	excluding lifting gear charges
21	CONT_SUM	INSTALL	TURBINE	LP	1	excluding lifting gear charges
22	CONT_SUM	INSTALL	TURBINE	MP	1	excluding lifting gear charges
23	CONT_SUM	REMOVE	DIAPHRAGM	MP	1	plus purging on time and materials basis.
24	CONT_SUM	REMOVE	DIAPHRAGM	MP	2	excluding lifting gear charges
25	CONT_SUM	STD EXCHANGE	DIAPHRAGM	MP	1	excluding lifting gear charges
26	CONT_SUM	STD EXCHANGE	ROTARY	LP	1	excluding lifting gear charges
27	CONT_SUM	STD EXCHANGE	ROTARY	MP	1	excluding lifting gear charges
28	CONT_SUM	STD EXCHANGE	TURBINE	LP	1	excluding lifting gear charges
29	CONT_SUM	STD EXCHANGE	TURBINE	MP	1	excluding lifting gear charges
30	CONT_SUM	STD INSTALL	DIAPHRAGM	MP	1	excluding lifting gear charges
31	CONT_SUM	STD INSTALL	ROTARY	LP	1	excluding lifting gear charges
32	CONT_SUM	STD INSTALL	ROTARY	MP	1	excluding lifting gear charges
33	CONT_SUM	STD INSTALL	TURBINE	LP	1	excluding lifting gear charges
34	CONT_SUM	STD INSTALL	TURBINE	MP	1	excluding lifting gear charges
35	CONT_SUM_QA	ADVERSARIAL	DIAPHRAGM	LP	1	plus purging on time and materials basis.
36	CONT_SUM_QA	ADVERSARIAL	DIAPHRAGM	MP	1	plus purging on time and materials basis.
37	CONT_SUM_QA	ADVERSARIAL	DIAPHRAGM	MP	2	excluding lifting gear charges
38	CONT_SUM_QA	ADVERSARIAL	ROTARY	LP	1	plus purging on time and materials basis.
39	CONT_SUM_QA	ADVERSARIAL	ROTARY	LP	2	excluding lifting gear charges
40	CONT_SUM_QA	ADVERSARIAL	ROTARY	MP	1	plus purging on time and materials basis.
41	CONT_SUM_QA	ADVERSARIAL	ROTARY	MP	2	excluding lifting gear charges
42	CONT_SUM_QA	ADVERSARIAL	TURBINE	LP	1	plus purging on time and materials basis.
43	CONT_SUM_QA	ADVERSARIAL	TURBINE	LP	2	excluding lifting gear charges
44	CONT_SUM_QA	ADVERSARIAL	TURBINE	MP	1	plus purging on time and materials basis.
45	CONT_SUM_QA	ADVERSARIAL	TURBINE	MP	2	excluding lifting gear charges
46	CONT_SUM_QA	EXCHANGE	DIAPHRAGM	MP	1	excluding lifting gear charges
47	CONT_SUM_QA	EXCHANGE	ROTARY	LP	1	excluding lifting gear charges
48	CONT_SUM_QA	EXCHANGE	ROTARY	MP	1	excluding lifting gear charges
49	CONT_SUM_QA	EXCHANGE	TURBINE	LP	1	excluding lifting gear charges
50	CONT_SUM_QA	EXCHANGE	TURBINE	MP	1	excluding lifting gear charges
51	CONT_SUM_QA	INSTALL	DIAPHRAGM	MP	1	excluding lifting gear charges
52	CONT_SUM_QA	INSTALL	ROTARY	LP	1	excluding lifting gear charges
53	CONT_SUM_QA	INSTALL	ROTARY	MP	1	excluding lifting gear charges
54	CONT_SUM_QA	INSTALL	TURBINE	LP	1	excluding lifting gear charges
55	CONT_SUM_QA	INSTALL	TURBINE	MP	1	excluding lifting gear charges
56	CONT_SUM_QA	REMOVE	DIAPHRAGM	MP	1	plus purging on time and materials basis.
57	CONT_SUM_QA	REMOVE	DIAPHRAGM	MP	2	excluding lifting gear charges
58	CONT_SUM_QA	STD EXCHANGE	DIAPHRAGM	MP	1	excluding lifting gear charges
59	CONT_SUM_QA	STD EXCHANGE	ROTARY	LP	1	excluding lifting gear charges
60	CONT_SUM_QA	STD EXCHANGE	ROTARY	MP	1	excluding lifting gear charges
61	CONT_SUM_QA	STD EXCHANGE	TURBINE	LP	1	excluding lifting gear charges
62	CONT_SUM_QA	STD EXCHANGE	TURBINE	MP	1	excluding lifting gear charges
63	CONT_SUM_QA	STD INSTALL	DIAPHRAGM	MP	1	excluding lifting gear charges
64	CONT_SUM_QA	STD INSTALL	ROTARY	LP	1	excluding lifting gear charges
65	CONT_SUM_QA	STD INSTALL	ROTARY	MP	1	excluding lifting gear charges
66	CONT_SUM_QA	STD INSTALL	TURBINE	LP	1	excluding lifting gear charges
67	CONT_SUM_QA	STD INSTALL	TURBINE	MP	1	excluding lifting gear charges
68	DESC_WORK	ADVERSARIAL	DIAPHRAGM	LP	1	Purging of downstream pipework.
69	DESC_WORK	ADVERSARIAL	DIAPHRAGM	MP	1	Purging of downstream pipework.
70	DESC_WORK	ADVERSARIAL	ROTARY	LP	1	Purging of downstream pipework.
71	DESC_WORK	ADVERSARIAL	ROTARY	MP	1	Purging of downstream pipework.
72	DESC_WORK	ADVERSARIAL	TURBINE	LP	1	Purging of downstream pipework.
73	DESC_WORK	ADVERSARIAL	TURBINE	MP	1	Purging of downstream pipework.
74	DESC_WORK	EXCHANGE	DIAPHRAGM	LP	1	Any service alteration required will need to be actioned by the UIP. Any outlet pipework alterations and the outlet pipework connection to the meter module will need to be actioned by others.
75	DESC_WORK	EXCHANGE	DIAPHRAGM	MP	1	Any service alteration required will need to be actioned by the UIP. Any outlet pipework alterations and the outlet pipework connection to the meter module will need to be actioned by others.
76	DESC_WORK	EXCHANGE	ROTARY	LP	1	Any service alteration required will need to be actioned by the UIP. Any outlet pipework alterations and the outlet pipework connection to the meter module will need to be actioned by others.
77	DESC_WORK	EXCHANGE	ROTARY	MP	1	Any service alteration required will need to be actioned by the UIP. Any outlet pipework alterations and the outlet pipework connection to the meter module will need to be actioned by others.
78	DESC_WORK	EXCHANGE	TURBINE	LP	1	Any service alteration required will need to be actioned by the UIP. Any outlet pipework alterations and the outlet pipework connection to the meter module will need to be actioned by others.
79	DESC_WORK	EXCHANGE	TURBINE	MP	1	Any service alteration required will need to be actioned by the UIP. Any outlet pipework alterations and the outlet pipework connection to the meter module will need to be actioned by others.
80	DESC_WORK	REMOVE	DIAPHRAGM	LP	1	Purging of downstream pipework.
81	DESC_WORK	REMOVE	DIAPHRAGM	MP	1	Purging of downstream pipework.
82	DESC_WORK	REMOVE	ROTARY	LP	1	Purging of downstream pipework.
83	DESC_WORK	REMOVE	ROTARY	LP	2	excluding lifting gear charges
84	DESC_WORK	REMOVE	ROTARY	MP	1	Purging of downstream pipework.
85	DESC_WORK	REMOVE	ROTARY	MP	2	excluding lifting gear charges
86	DESC_WORK	REMOVE	TURBINE	LP	1	Purging of downstream pipework.
87	DESC_WORK	REMOVE	TURBINE	LP	2	excluding lifting gear charges
88	DESC_WORK	REMOVE	TURBINE	MP	1	Purging of downstream pipework.
89	DESC_WORK	REMOVE	TURBINE	MP	2	excluding lifting gear charges
90	DESC_WORK	STD EXCHANGE	DIAPHRAGM	LP	1	Any service alteration required will need to be actioned by the UIP. Any outlet pipework alterations and the outlet pipework connection to the meter module will need to be actioned by others.
91	DESC_WORK	STD EXCHANGE	DIAPHRAGM	MP	1	Any service alteration required will need to be actioned by the UIP. Any outlet pipework alterations and the outlet pipework connection to the meter module will need to be actioned by others.
92	DESC_WORK	STD EXCHANGE	ROTARY	LP	1	Any service alteration required will need to be actioned by the UIP. Any outlet pipework alterations and the outlet pipework connection to the meter module will need to be actioned by others.
93	DESC_WORK	STD EXCHANGE	ROTARY	MP	1	Any service alteration required will need to be actioned by the UIP. Any outlet pipework alterations and the outlet pipework connection to the meter module will need to be actioned by others.
94	DESC_WORK	STD EXCHANGE	TURBINE	LP	1	Any service alteration required will need to be actioned by the UIP. Any outlet pipework alterations and the outlet pipework connection to the meter module will need to be actioned by others.
95	DESC_WORK	STD EXCHANGE	TURBINE	MP	1	Any service alteration required will need to be actioned by the UIP. Any outlet pipework alterations and the outlet pipework connection to the meter module will need to be actioned by others.
96	TERM_COND	ADDON	DIAPHRAGM	LP	1	This quotation is based on there being a working LF connection on the existing meter.
97	TERM_COND	ADDON	DIAPHRAGM	LP	2	This quotation does not include for the provision of a separate instrumentation cabinet.
98	TERM_COND	ADDON	DIAPHRAGM	LP	3	Electrical Connections to gas meters are subject to the assessment of the hazardous area around the meter. This is largely affected by the ventilation in the housing. Should the ventilation be found to be inadequate the connection will not be made and the requirements to allow the connection reported to you.
99	TERM_COND	ADDON	DIAPHRAGM	MP	1	This quotation is based on there being a working LF connection on the existing meter.
100	TERM_COND	ADDON	DIAPHRAGM	MP	2	This quotation does not include for the provision of a separate instrumentation cabinet.
101	TERM_COND	ADDON	DIAPHRAGM	MP	3	Electrical Connections to gas meters are subject to the assessment of the hazardous area around the meter. This is largely affected by the ventilation in the housing. Should the ventilation be found to be inadequate the connection will not be made and the requirements to allow the connection reported to you.
102	TERM_COND	ADDON	ROTARY	LP	1	This quotation is based on there being a working LF connection on the existing meter.
103	TERM_COND	ADDON	ROTARY	LP	2	This quotation does not include for the provision of a separate instrumentation cabinet.
104	TERM_COND	ADDON	ROTARY	LP	3	Electrical Connections to gas meters are subject to the assessment of the hazardous area around the meter. This is largely affected by the ventilation in the housing. Should the ventilation be found to be inadequate the connection will not be made and the requirements to allow the connection reported to you.
105	TERM_COND	ADDON	ROTARY	MP	1	This quotation is based on there being a working LF connection on the existing meter.
106	TERM_COND	ADDON	ROTARY	MP	2	This quotation does not include for the provision of a separate instrumentation cabinet.
107	TERM_COND	ADDON	ROTARY	MP	3	Electrical Connections to gas meters are subject to the assessment of the hazardous area around the meter. This is largely affected by the ventilation in the housing. Should the ventilation be found to be inadequate the connection will not be made and the requirements to allow the connection reported to you.
108	TERM_COND	ADDON	TURBINE	LP	1	This quotation is based on there being a working LF connection on the existing meter.
109	TERM_COND	ADDON	TURBINE	LP	2	This quotation does not include for the provision of a separate instrumentation cabinet.
110	TERM_COND	ADDON	TURBINE	LP	3	Electrical Connections to gas meters are subject to the assessment of the hazardous area around the meter. This is largely affected by the ventilation in the housing. Should the ventilation be found to be inadequate the connection will not be made and the requirements to allow the connection reported to you.
111	TERM_COND	ADDON	TURBINE	MP	1	This quotation is based on there being a working LF connection on the existing meter.
112	TERM_COND	ADDON	TURBINE	MP	2	This quotation does not include for the provision of a separate instrumentation cabinet.
113	TERM_COND	ADDON	TURBINE	MP	3	Electrical Connections to gas meters are subject to the assessment of the hazardous area around the meter. This is largely affected by the ventilation in the housing. Should the ventilation be found to be inadequate the connection will not be made and the requirements to allow the connection reported to you.
114	TERM_COND	ADVERSARIAL	DIAPHRAGM	LP	1	This quotation is based on a low pressure service tier. If the pressure tier if found not to be low pressure, this will be subject to a new quotation or variation and planned meter works will not commence.
115	TERM_COND	ADVERSARIAL	DIAPHRAGM	LP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
116	TERM_COND	ADVERSARIAL	ROTARY	LP	1	This quotation is based on a low pressure service tier. If the pressure tier if found not to be low pressure, this will be subject to a new quotation or variation and planned meter works will not commence.
117	TERM_COND	ADVERSARIAL	ROTARY	LP	2	Lifting gear if required will be charged at a rate of £400 per day.
118	TERM_COND	ADVERSARIAL	ROTARY	LP	3	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
119	TERM_COND	ADVERSARIAL	ROTARY	MP	1	Lifting gear if required will be charged at a rate of £400 per day.
120	TERM_COND	ADVERSARIAL	ROTARY	MP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
121	TERM_COND	ADVERSARIAL	TURBINE	LP	1	This quotation is based on a low pressure service tier. If the pressure tier if found not to be low pressure, this will be subject to a new quotation or variation and planned meter works will not commence.
122	TERM_COND	ADVERSARIAL	TURBINE	LP	2	Lifting gear if required will be charged at a rate of £400 per day.
123	TERM_COND	ADVERSARIAL	TURBINE	LP	3	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
124	TERM_COND	ADVERSARIAL	TURBINE	MP	1	Lifting gear if required will be charged at a rate of £400 per day.
125	TERM_COND	ADVERSARIAL	TURBINE	MP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
126	TERM_COND	EXCHANGE	DIAPHRAGM	LP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
127	TERM_COND	EXCHANGE	DIAPHRAGM	LP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
128	TERM_COND	EXCHANGE	DIAPHRAGM	LP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
129	TERM_COND	EXCHANGE	DIAPHRAGM	LP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure of 25 mbar under Qmax load at the ECV outlet point.
130	TERM_COND	EXCHANGE	DIAPHRAGM	LP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
131	TERM_COND	EXCHANGE	DIAPHRAGM	LP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
132	TERM_COND	EXCHANGE	DIAPHRAGM	LP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
133	TERM_COND	EXCHANGE	DIAPHRAGM	LP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
134	TERM_COND	EXCHANGE	DIAPHRAGM	LP	9	This quotation is based on the exchange being completed on the same day and the new meter module being attached to the existing ECV.
135	TERM_COND	EXCHANGE	DIAPHRAGM	LP	10	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
136	TERM_COND	EXCHANGE	DIAPHRAGM	MP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
137	TERM_COND	EXCHANGE	DIAPHRAGM	MP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
138	TERM_COND	EXCHANGE	DIAPHRAGM	MP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
139	TERM_COND	EXCHANGE	DIAPHRAGM	MP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure as described in table 1 (ECV Outlet) under Qmax load at the ECV outlet point.
140	TERM_COND	EXCHANGE	DIAPHRAGM	MP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
141	TERM_COND	EXCHANGE	DIAPHRAGM	MP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
142	TERM_COND	EXCHANGE	DIAPHRAGM	MP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
143	TERM_COND	EXCHANGE	DIAPHRAGM	MP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
144	TERM_COND	EXCHANGE	DIAPHRAGM	MP	9	This quotation is based on the exchange being completed on the same day and the new meter module being attached to the existing ECV.
145	TERM_COND	EXCHANGE	DIAPHRAGM	MP	10	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
146	TERM_COND	EXCHANGE	DIAPHRAGM	MP	11	Lifting gear if required will be charged at a rate of £400 per day.
147	TERM_COND	EXCHANGE	ROTARY	LP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
148	TERM_COND	EXCHANGE	ROTARY	LP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
149	TERM_COND	EXCHANGE	ROTARY	LP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
150	TERM_COND	EXCHANGE	ROTARY	LP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure of 25 mbar under Qmax load at the ECV outlet point.
151	TERM_COND	EXCHANGE	ROTARY	LP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
152	TERM_COND	EXCHANGE	ROTARY	LP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
153	TERM_COND	EXCHANGE	ROTARY	LP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
154	TERM_COND	EXCHANGE	ROTARY	LP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
155	TERM_COND	EXCHANGE	ROTARY	LP	9	This quotation is based on the exchange being completed on the same day and the new meter module being attached to the existing ECV.
156	TERM_COND	EXCHANGE	ROTARY	LP	10	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
157	TERM_COND	EXCHANGE	ROTARY	LP	11	Lifting gear if required will be charged at a rate of £400 per day.
158	TERM_COND	EXCHANGE	ROTARY	MP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
159	TERM_COND	EXCHANGE	ROTARY	MP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
160	TERM_COND	EXCHANGE	ROTARY	MP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
161	TERM_COND	EXCHANGE	ROTARY	MP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure as described in table 1 (ECV Outlet) under Qmax load at the ECV outlet point.
162	TERM_COND	EXCHANGE	ROTARY	MP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
163	TERM_COND	EXCHANGE	ROTARY	MP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
164	TERM_COND	EXCHANGE	ROTARY	MP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
165	TERM_COND	EXCHANGE	ROTARY	MP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
166	TERM_COND	EXCHANGE	ROTARY	MP	9	This quotation is based on the exchange being completed on the same day and the new meter module being attached to the existing ECV.
167	TERM_COND	EXCHANGE	ROTARY	MP	10	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
168	TERM_COND	EXCHANGE	ROTARY	MP	11	Lifting gear if required will be charged at a rate of £400 per day.
169	TERM_COND	EXCHANGE	TURBINE	LP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
170	TERM_COND	EXCHANGE	TURBINE	LP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed..
171	TERM_COND	EXCHANGE	TURBINE	LP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
172	TERM_COND	EXCHANGE	TURBINE	LP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure of 25 mbar under Qmax load at the ECV outlet point.
173	TERM_COND	EXCHANGE	TURBINE	LP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
174	TERM_COND	EXCHANGE	TURBINE	LP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
175	TERM_COND	EXCHANGE	TURBINE	LP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
176	TERM_COND	EXCHANGE	TURBINE	LP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
177	TERM_COND	EXCHANGE	TURBINE	LP	9	This quotation is based on the exchange being completed on the same day and the new meter module being attached to the existing ECV.
178	TERM_COND	EXCHANGE	TURBINE	LP	10	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
179	TERM_COND	EXCHANGE	TURBINE	LP	11	Lifting gear if required will be charged at a rate of £400 per day.
180	TERM_COND	EXCHANGE	TURBINE	MP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
181	TERM_COND	EXCHANGE	TURBINE	MP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
182	TERM_COND	EXCHANGE	TURBINE	MP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
183	TERM_COND	EXCHANGE	TURBINE	MP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure as described in table 1 (ECV Outlet) under Qmax load at the ECV outlet point.
184	TERM_COND	EXCHANGE	TURBINE	MP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
185	TERM_COND	EXCHANGE	TURBINE	MP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
186	TERM_COND	EXCHANGE	TURBINE	MP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
187	TERM_COND	EXCHANGE	TURBINE	MP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
188	TERM_COND	EXCHANGE	TURBINE	MP	9	This quotation is based on the exchange being completed on the same day and the new meter module being attached to the existing ECV.
189	TERM_COND	EXCHANGE	TURBINE	MP	10	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
190	TERM_COND	EXCHANGE	TURBINE	MP	11	Lifting gear if required will be charged at a rate of £400 per day.
191	TERM_COND	INSTALL	DIAPHRAGM	LP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
192	TERM_COND	INSTALL	DIAPHRAGM	LP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
193	TERM_COND	INSTALL	DIAPHRAGM	LP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
194	TERM_COND	INSTALL	DIAPHRAGM	LP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure of 25 mbar under Qmax load at the ECV outlet point.
195	TERM_COND	INSTALL	DIAPHRAGM	LP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
196	TERM_COND	INSTALL	DIAPHRAGM	LP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
197	TERM_COND	INSTALL	DIAPHRAGM	LP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
198	TERM_COND	INSTALL	DIAPHRAGM	LP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
199	TERM_COND	INSTALL	DIAPHRAGM	LP	9	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
200	TERM_COND	INSTALL	DIAPHRAGM	MP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
201	TERM_COND	INSTALL	DIAPHRAGM	MP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
202	TERM_COND	INSTALL	DIAPHRAGM	MP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
203	TERM_COND	INSTALL	DIAPHRAGM	MP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure as described in table 1 (ECV Outlet) under Qmax load at the ECV outlet point.
204	TERM_COND	INSTALL	DIAPHRAGM	MP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
205	TERM_COND	INSTALL	DIAPHRAGM	MP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
206	TERM_COND	INSTALL	DIAPHRAGM	MP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
207	TERM_COND	INSTALL	DIAPHRAGM	MP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
208	TERM_COND	INSTALL	DIAPHRAGM	MP	9	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
209	TERM_COND	INSTALL	DIAPHRAGM	MP	10	Lifting gear if required will be charged at a rate of £400 per day.
210	TERM_COND	INSTALL	ROTARY	LP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
211	TERM_COND	INSTALL	ROTARY	LP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
212	TERM_COND	INSTALL	ROTARY	LP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
213	TERM_COND	INSTALL	ROTARY	LP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure of 25 mbar under Qmax load at the ECV outlet point.
214	TERM_COND	INSTALL	ROTARY	LP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
215	TERM_COND	INSTALL	ROTARY	LP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
216	TERM_COND	INSTALL	ROTARY	LP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
217	TERM_COND	INSTALL	ROTARY	LP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
218	TERM_COND	INSTALL	ROTARY	LP	9	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
219	TERM_COND	INSTALL	ROTARY	LP	10	Lifting gear if required will be charged at a rate of £400 per day.
220	TERM_COND	INSTALL	ROTARY	MP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
221	TERM_COND	INSTALL	ROTARY	MP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
222	TERM_COND	INSTALL	ROTARY	MP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
223	TERM_COND	INSTALL	ROTARY	MP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure as described in table 1 (ECV Outlet) under Qmax load at the ECV outlet point.
224	TERM_COND	INSTALL	ROTARY	MP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
225	TERM_COND	INSTALL	ROTARY	MP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
226	TERM_COND	INSTALL	ROTARY	MP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
227	TERM_COND	INSTALL	ROTARY	MP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
228	TERM_COND	INSTALL	ROTARY	MP	9	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
229	TERM_COND	INSTALL	ROTARY	MP	10	Lifting gear if required will be charged at a rate of £400 per day.
230	TERM_COND	INSTALL	TURBINE	LP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
231	TERM_COND	INSTALL	TURBINE	LP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
232	TERM_COND	INSTALL	TURBINE	LP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
233	TERM_COND	INSTALL	TURBINE	LP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure of 25 mbar under Qmax load at the ECV outlet point.
234	TERM_COND	INSTALL	TURBINE	LP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
235	TERM_COND	INSTALL	TURBINE	LP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
236	TERM_COND	INSTALL	TURBINE	LP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
237	TERM_COND	INSTALL	TURBINE	LP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
238	TERM_COND	INSTALL	TURBINE	LP	9	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
239	TERM_COND	INSTALL	TURBINE	LP	10	Lifting gear if required will be charged at a rate of £400 per day.
240	TERM_COND	INSTALL	TURBINE	MP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
241	TERM_COND	INSTALL	TURBINE	MP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
242	TERM_COND	INSTALL	TURBINE	MP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
243	TERM_COND	INSTALL	TURBINE	MP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure as described in table 1 (ECV Outlet) under Qmax load at the ECV outlet point.
244	TERM_COND	INSTALL	TURBINE	MP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
245	TERM_COND	INSTALL	TURBINE	MP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
246	TERM_COND	INSTALL	TURBINE	MP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
247	TERM_COND	INSTALL	TURBINE	MP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
248	TERM_COND	INSTALL	TURBINE	MP	9	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
249	TERM_COND	INSTALL	TURBINE	MP	10	Lifting gear if required will be charged at a rate of £400 per day.
250	TERM_COND	OFMAT	DIAPHRAGM	LP	1	This charge will only be applicable if the meter accuracy test identifies the meter to be working correctly.
251	TERM_COND	OFMAT	DIAPHRAGM	LP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
252	TERM_COND	OFMAT	DIAPHRAGM	MP	1	This charge will only be applicable if the meter accuracy test identifies the meter to be working correctly.
253	TERM_COND	OFMAT	DIAPHRAGM	MP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
254	TERM_COND	OFMAT	ROTARY	LP	1	This charge will only be applicable if the meter accuracy test identifies the meter to be working correctly.
255	TERM_COND	OFMAT	ROTARY	LP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
256	TERM_COND	OFMAT	ROTARY	MP	1	This charge will only be applicable if the meter accuracy test identifies the meter to be working correctly.
257	TERM_COND	OFMAT	ROTARY	MP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
258	TERM_COND	OFMAT	TURBINE	LP	1	This charge will only be applicable if the meter accuracy test identifies the meter to be working correctly.
259	TERM_COND	OFMAT	TURBINE	LP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
260	TERM_COND	OFMAT	TURBINE	MP	1	This charge will only be applicable if the meter accuracy test identifies the meter to be working correctly.
261	TERM_COND	OFMAT	TURBINE	MP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
262	TERM_COND	REMOVE	DIAPHRAGM	LP	1	This quotation is based on a low pressure service tier. If the pressure tier if found not to be low pressure, this will be subject to a new quotation or variation and planned meter works will not commence.
263	TERM_COND	REMOVE	DIAPHRAGM	LP	2	Where purging of downstream supplies is necessary but has not been requested as part of the meter removal work, the meter will not be removed until the downstream supplies have been made safe by purging.
264	TERM_COND	REMOVE	DIAPHRAGM	LP	3	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
265	TERM_COND	REMOVE	DIAPHRAGM	MP	1	Where purging of downstream supplies is necessary but has not been requested as part of the meter removal work, the meter will not be removed until the downstream supplies have been made safe by purging.
266	TERM_COND	REMOVE	DIAPHRAGM	MP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
267	TERM_COND	REMOVE	DIAPHRAGM	MP	3	Lifting gear if required will be charged at a rate of £400 per day.
268	TERM_COND	REMOVE	ROTARY	LP	1	This quotation is based on a low pressure service tier. If the pressure tier if found not to be low pressure, this will be subject to a new quotation or variation and planned meter works will not commence.
269	TERM_COND	REMOVE	ROTARY	LP	2	Where purging of downstream supplies is necessary but has not been requested as part of the meter removal work, the meter will not be removed until the downstream supplies have been made safe by purging.
270	TERM_COND	REMOVE	ROTARY	LP	3	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
271	TERM_COND	REMOVE	ROTARY	LP	4	Lifting gear if required will be charged at a rate of £400 per day.
272	TERM_COND	REMOVE	ROTARY	MP	1	Where purging of downstream supplies is necessary but has not been requested as part of the meter removal work, the meter will not be removed until the downstream supplies have been made safe by purging.
273	TERM_COND	REMOVE	ROTARY	MP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
274	TERM_COND	REMOVE	ROTARY	MP	3	Lifting gear if required will be charged at a rate of £400 per day.
275	TERM_COND	REMOVE	TURBINE	LP	1	This quotation is based on a low pressure service tier. If the pressure tier if found not to be low pressure, this will be subject to a new quotation or variation and planned meter works will not commence.
276	TERM_COND	REMOVE	TURBINE	LP	2	Where purging of downstream supplies is necessary but has not been requested as part of the meter removal work, the meter will not be removed until the downstream supplies have been made safe by purging.
277	TERM_COND	REMOVE	TURBINE	LP	3	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
278	TERM_COND	REMOVE	TURBINE	LP	4	Lifting gear if required will be charged at a rate of £400 per day.
279	TERM_COND	REMOVE	TURBINE	MP	1	Where purging of downstream supplies is necessary but has not been requested as part of the meter removal work, the meter will not be removed until the downstream supplies have been made safe by purging.
280	TERM_COND	REMOVE	TURBINE	MP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
281	TERM_COND	REMOVE	TURBINE	MP	3	Lifting gear if required will be charged at a rate of £400 per day.
282	TERM_COND	STD EXCHANGE	DIAPHRAGM	LP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
283	TERM_COND	STD EXCHANGE	DIAPHRAGM	LP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
284	TERM_COND	STD EXCHANGE	DIAPHRAGM	LP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
285	TERM_COND	STD EXCHANGE	DIAPHRAGM	LP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure of 25 mbar under Qmax load at the ECV outlet point.
286	TERM_COND	STD EXCHANGE	DIAPHRAGM	LP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
287	TERM_COND	STD EXCHANGE	DIAPHRAGM	LP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
288	TERM_COND	STD EXCHANGE	DIAPHRAGM	LP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
289	TERM_COND	STD EXCHANGE	DIAPHRAGM	LP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
290	TERM_COND	STD EXCHANGE	DIAPHRAGM	LP	9	This quotation is based on the exchange being completed on the same day and the new meter module being attached to the existing ECV.
291	TERM_COND	STD EXCHANGE	DIAPHRAGM	LP	10	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
292	TERM_COND	STD EXCHANGE	DIAPHRAGM	MP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
293	TERM_COND	STD EXCHANGE	DIAPHRAGM	MP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
294	TERM_COND	STD EXCHANGE	DIAPHRAGM	MP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
295	TERM_COND	STD EXCHANGE	DIAPHRAGM	MP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure as described in table 1 (ECV Outlet) under Qmax load at the ECV outlet point.
296	TERM_COND	STD EXCHANGE	DIAPHRAGM	MP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
297	TERM_COND	STD EXCHANGE	DIAPHRAGM	MP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
298	TERM_COND	STD EXCHANGE	DIAPHRAGM	MP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
299	TERM_COND	STD EXCHANGE	DIAPHRAGM	MP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
300	TERM_COND	STD EXCHANGE	DIAPHRAGM	MP	9	This quotation is based on the exchange being completed on the same day and the new meter module being attached to the existing ECV.
301	TERM_COND	STD EXCHANGE	DIAPHRAGM	MP	10	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
302	TERM_COND	STD EXCHANGE	DIAPHRAGM	MP	11	Lifting gear if required will be charged at a rate of £400 per day.
303	TERM_COND	STD EXCHANGE	ROTARY	LP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
304	TERM_COND	STD EXCHANGE	ROTARY	LP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
305	TERM_COND	STD EXCHANGE	ROTARY	LP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
306	TERM_COND	STD EXCHANGE	ROTARY	LP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure of 25 mbar under Qmax load at the ECV outlet point.
307	TERM_COND	STD EXCHANGE	ROTARY	LP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
308	TERM_COND	STD EXCHANGE	ROTARY	LP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
309	TERM_COND	STD EXCHANGE	ROTARY	LP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
310	TERM_COND	STD EXCHANGE	ROTARY	LP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
311	TERM_COND	STD EXCHANGE	ROTARY	LP	9	This quotation is based on the exchange being completed on the same day and the new meter module being attached to the existing ECV.
312	TERM_COND	STD EXCHANGE	ROTARY	LP	10	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
313	TERM_COND	STD EXCHANGE	ROTARY	LP	11	Lifting gear if required will be charged at a rate of £400 per day.
314	TERM_COND	STD EXCHANGE	ROTARY	MP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
315	TERM_COND	STD EXCHANGE	ROTARY	MP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
316	TERM_COND	STD EXCHANGE	ROTARY	MP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
317	TERM_COND	STD EXCHANGE	ROTARY	MP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure as described in table 1 (ECV Outlet) under Qmax load at the ECV outlet point.
318	TERM_COND	STD EXCHANGE	ROTARY	MP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
319	TERM_COND	STD EXCHANGE	ROTARY	MP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
320	TERM_COND	STD EXCHANGE	ROTARY	MP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
321	TERM_COND	STD EXCHANGE	ROTARY	MP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
322	TERM_COND	STD EXCHANGE	ROTARY	MP	9	This quotation is based on the exchange being completed on the same day and the new meter module being attached to the existing ECV.
323	TERM_COND	STD EXCHANGE	ROTARY	MP	10	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
324	TERM_COND	STD EXCHANGE	ROTARY	MP	11	Lifting gear if required will be charged at a rate of £400 per day.
325	TERM_COND	STD EXCHANGE	TURBINE	LP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
326	TERM_COND	STD EXCHANGE	TURBINE	LP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
327	TERM_COND	STD EXCHANGE	TURBINE	LP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
328	TERM_COND	STD EXCHANGE	TURBINE	LP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure of 25 mbar under Qmax load at the ECV outlet point.
329	TERM_COND	STD EXCHANGE	TURBINE	LP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
330	TERM_COND	STD EXCHANGE	TURBINE	LP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
331	TERM_COND	STD EXCHANGE	TURBINE	LP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
332	TERM_COND	STD EXCHANGE	TURBINE	LP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
333	TERM_COND	STD EXCHANGE	TURBINE	LP	9	This quotation is based on the exchange being completed on the same day and the new meter module being attached to the existing ECV.
334	TERM_COND	STD EXCHANGE	TURBINE	LP	10	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
335	TERM_COND	STD EXCHANGE	TURBINE	LP	11	Lifting gear if required will be charged at a rate of £400 per day.
336	TERM_COND	STD EXCHANGE	TURBINE	MP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
337	TERM_COND	STD EXCHANGE	TURBINE	MP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
338	TERM_COND	STD EXCHANGE	TURBINE	MP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
339	TERM_COND	STD EXCHANGE	TURBINE	MP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure as described in table 1 (ECV Outlet) under Qmax load at the ECV outlet point.
340	TERM_COND	STD EXCHANGE	TURBINE	MP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
341	TERM_COND	STD EXCHANGE	TURBINE	MP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
342	TERM_COND	STD EXCHANGE	TURBINE	MP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
343	TERM_COND	STD EXCHANGE	TURBINE	MP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
344	TERM_COND	STD EXCHANGE	TURBINE	MP	9	This quotation is based on the exchange being completed on the same day and the new meter module being attached to the existing ECV.
345	TERM_COND	STD EXCHANGE	TURBINE	MP	10	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
346	TERM_COND	STD EXCHANGE	TURBINE	MP	11	Lifting gear if required will be charged at a rate of £400 per day.
347	TERM_COND	STD INSTALL	DIAPHRAGM	LP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
348	TERM_COND	STD INSTALL	DIAPHRAGM	LP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
349	TERM_COND	STD INSTALL	DIAPHRAGM	LP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
350	TERM_COND	STD INSTALL	DIAPHRAGM	LP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure of 25 mbar under Qmax load at the ECV outlet point.
351	TERM_COND	STD INSTALL	DIAPHRAGM	LP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
352	TERM_COND	STD INSTALL	DIAPHRAGM	LP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
353	TERM_COND	STD INSTALL	DIAPHRAGM	LP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
354	TERM_COND	STD INSTALL	DIAPHRAGM	LP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
355	TERM_COND	STD INSTALL	DIAPHRAGM	LP	9	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
356	TERM_COND	STD INSTALL	DIAPHRAGM	MP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
357	TERM_COND	STD INSTALL	DIAPHRAGM	MP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
358	TERM_COND	STD INSTALL	DIAPHRAGM	MP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
359	TERM_COND	STD INSTALL	DIAPHRAGM	MP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure as described in table 1 (ECV Outlet) under Qmax load at the ECV outlet point.
360	TERM_COND	STD INSTALL	DIAPHRAGM	MP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
361	TERM_COND	STD INSTALL	DIAPHRAGM	MP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
362	TERM_COND	STD INSTALL	DIAPHRAGM	MP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
363	TERM_COND	STD INSTALL	DIAPHRAGM	MP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
364	TERM_COND	STD INSTALL	DIAPHRAGM	MP	9	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
365	TERM_COND	STD INSTALL	DIAPHRAGM	MP	10	Lifting gear if required will be charged at a rate of £400 per day.
366	TERM_COND	STD INSTALL	ROTARY	LP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
367	TERM_COND	STD INSTALL	ROTARY	LP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
368	TERM_COND	STD INSTALL	ROTARY	LP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
369	TERM_COND	STD INSTALL	ROTARY	LP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure of 25 mbar under Qmax load at the ECV outlet point.
370	TERM_COND	STD INSTALL	ROTARY	LP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
371	TERM_COND	STD INSTALL	ROTARY	LP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
372	TERM_COND	STD INSTALL	ROTARY	LP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
373	TERM_COND	STD INSTALL	ROTARY	LP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
374	TERM_COND	STD INSTALL	ROTARY	LP	9	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
375	TERM_COND	STD INSTALL	ROTARY	LP	10	Lifting gear if required will be charged at a rate of £400 per day.
376	TERM_COND	STD INSTALL	ROTARY	MP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
377	TERM_COND	STD INSTALL	ROTARY	MP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
378	TERM_COND	STD INSTALL	ROTARY	MP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
379	TERM_COND	STD INSTALL	ROTARY	MP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure as described in table 1 (ECV Outlet) under Qmax load at the ECV outlet point.
380	TERM_COND	STD INSTALL	ROTARY	MP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
381	TERM_COND	STD INSTALL	ROTARY	MP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
382	TERM_COND	STD INSTALL	ROTARY	MP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
383	TERM_COND	STD INSTALL	ROTARY	MP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
384	TERM_COND	STD INSTALL	ROTARY	MP	9	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
385	TERM_COND	STD INSTALL	ROTARY	MP	10	Lifting gear if required will be charged at a rate of £400 per day.
386	TERM_COND	STD INSTALL	TURBINE	LP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
387	TERM_COND	STD INSTALL	TURBINE	LP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
388	TERM_COND	STD INSTALL	TURBINE	LP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
389	TERM_COND	STD INSTALL	TURBINE	LP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure of 25 mbar under Qmax load at the ECV outlet point.
390	TERM_COND	STD INSTALL	TURBINE	LP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
391	TERM_COND	STD INSTALL	TURBINE	LP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
392	TERM_COND	STD INSTALL	TURBINE	LP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
393	TERM_COND	STD INSTALL	TURBINE	LP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
394	TERM_COND	STD INSTALL	TURBINE	LP	9	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
395	TERM_COND	STD INSTALL	TURBINE	LP	10	Lifting gear if required will be charged at a rate of £400 per day.
396	TERM_COND	STD INSTALL	TURBINE	MP	1	Please note that all the sizes and dimensions stated are indicative and are based on current practice at the time of quotation. These are subject to change and must be confirmed at placement of order.
397	TERM_COND	STD INSTALL	TURBINE	MP	2	Housings must have a free ventilation area equal to/exceeding 3% floor area. Minimum Housing requirements for this module are listed in the Meter Housing Detail section above. Failure to provide adequate housing will result in the job not being completed.
398	TERM_COND	STD INSTALL	TURBINE	MP	3	Minimum Base dimension requirements for this module are listed in the Meter Housing and Base section above. Failure not to provide an accurate base will result in the job not being completed.
399	TERM_COND	STD INSTALL	TURBINE	MP	4	The Supply Point must be suitably sized and positioned to provide a minimum pressure as described in table 1 (ECV Outlet) under Qmax load at the ECV outlet point.
400	TERM_COND	STD INSTALL	TURBINE	MP	5	This quotation is based on a the inlet orientation and outlet orientation described in table 3 and the ECV being installed to the dimensions provided.
401	TERM_COND	STD INSTALL	TURBINE	MP	6	The meter module is a single stream supply with no bypass facility. During maintenance operations on the meter installation it may be necessary to isolate the supply temporarily
402	TERM_COND	STD INSTALL	TURBINE	MP	7	It is critical that the module inlet dimensions and orientation are given to the UIP when service works are taken place.
403	TERM_COND	STD INSTALL	TURBINE	MP	8	The proposed meter module has a Qmin specified in table 2 and is based on the requested Qmax also specified in table 2.
404	TERM_COND	STD INSTALL	TURBINE	MP	9	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
405	TERM_COND	STD INSTALL	TURBINE	MP	10	Lifting gear if required will be charged at a rate of £400 per day.
406	CONT_SUM	STD REMOVE	DIAPHRAGM	MP	1	plus purging on time and materials basis.
407	CONT_SUM	STD REMOVE	DIAPHRAGM	MP	2	excluding lifting gear charges
408	CONT_SUM_QA	STD REMOVE	DIAPHRAGM	MP	1	plus purging on time and materials basis.
409	CONT_SUM_QA	STD REMOVE	DIAPHRAGM	MP	2	excluding lifting gear charges
410	DESC_WORK	STD REMOVE	DIAPHRAGM	LP	1	Purging of downstream pipework.
411	DESC_WORK	STD REMOVE	DIAPHRAGM	MP	1	Purging of downstream pipework.
412	DESC_WORK	STD REMOVE	ROTARY	LP	1	Purging of downstream pipework.
413	DESC_WORK	STD REMOVE	ROTARY	LP	2	excluding lifting gear charges
414	DESC_WORK	STD REMOVE	ROTARY	MP	1	Purging of downstream pipework.
415	DESC_WORK	STD REMOVE	ROTARY	MP	2	excluding lifting gear charges
416	DESC_WORK	STD REMOVE	TURBINE	LP	1	Purging of downstream pipework.
417	DESC_WORK	STD REMOVE	TURBINE	LP	2	excluding lifting gear charges
418	DESC_WORK	STD REMOVE	TURBINE	MP	1	Purging of downstream pipework.
419	DESC_WORK	STD REMOVE	TURBINE	MP	2	excluding lifting gear charges
420	TERM_COND	STD REMOVE	DIAPHRAGM	LP	1	This quotation is based on a low pressure service tier. If the pressure tier if found not to be low pressure, this will be subject to a new quotation or variation and planned meter works will not commence.
421	TERM_COND	STD REMOVE	DIAPHRAGM	LP	2	Where purging of downstream supplies is necessary but has not been requested as part of the meter removal work, the meter will not be removed until the downstream supplies have been made safe by purging.
422	TERM_COND	STD REMOVE	DIAPHRAGM	LP	3	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
423	TERM_COND	STD REMOVE	DIAPHRAGM	MP	1	Where purging of downstream supplies is necessary but has not been requested as part of the meter removal work, the meter will not be removed until the downstream supplies have been made safe by purging.
424	TERM_COND	STD REMOVE	DIAPHRAGM	MP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
425	TERM_COND	STD REMOVE	DIAPHRAGM	MP	3	Lifting gear if required will be charged at a rate of £400 per day.
426	TERM_COND	STD REMOVE	ROTARY	LP	1	This quotation is based on a low pressure service tier. If the pressure tier if found not to be low pressure, this will be subject to a new quotation or variation and planned meter works will not commence.
427	TERM_COND	STD REMOVE	ROTARY	LP	2	Where purging of downstream supplies is necessary but has not been requested as part of the meter removal work, the meter will not be removed until the downstream supplies have been made safe by purging.
428	TERM_COND	STD REMOVE	ROTARY	LP	3	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
429	TERM_COND	STD REMOVE	ROTARY	LP	4	Lifting gear if required will be charged at a rate of £400 per day.
430	TERM_COND	STD REMOVE	ROTARY	MP	1	Where purging of downstream supplies is necessary but has not been requested as part of the meter removal work, the meter will not be removed until the downstream supplies have been made safe by purging.
431	TERM_COND	STD REMOVE	ROTARY	MP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
432	TERM_COND	STD REMOVE	ROTARY	MP	3	Lifting gear if required will be charged at a rate of £400 per day.
433	TERM_COND	STD REMOVE	TURBINE	LP	1	This quotation is based on a low pressure service tier. If the pressure tier if found not to be low pressure, this will be subject to a new quotation or variation and planned meter works will not commence.
434	TERM_COND	STD REMOVE	TURBINE	LP	2	Where purging of downstream supplies is necessary but has not been requested as part of the meter removal work, the meter will not be removed until the downstream supplies have been made safe by purging.
435	TERM_COND	STD REMOVE	TURBINE	LP	3	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
436	TERM_COND	STD REMOVE	TURBINE	LP	4	Lifting gear if required will be charged at a rate of £400 per day.
437	TERM_COND	STD REMOVE	TURBINE	MP	1	Where purging of downstream supplies is necessary but has not been requested as part of the meter removal work, the meter will not be removed until the downstream supplies have been made safe by purging.
438	TERM_COND	STD REMOVE	TURBINE	MP	2	This quotation is subject to there being sufficient access available and free from any obstructions. Failure to provide sufficient access may result in the job being aborted
439	TERM_COND	STD REMOVE	TURBINE	MP	3	Lifting gear if required will be charged at a rate of £400 per day.